{"id":15854,"date":"2023-12-18T16:30:15","date_gmt":"2023-12-18T16:30:15","guid":{"rendered":"https:\/\/www.fhfurrblogs.jdmps.com\/delmarva-area\/?page_id=15854"},"modified":"2025-07-30T07:12:28","modified_gmt":"2025-07-30T07:12:28","slug":"maintenance","status":"publish","type":"page","link":"https:\/\/fhfurrblogs.jdmps.com\/delmarva-area\/heating\/maintenance\/","title":{"rendered":"Heating Maintenance In Georgetown, DE"},"content":{"rendered":"

To escape the cold in Georgetown, homeowners need reliable and efficient heating. F.H. Furr Plumbing, Heating, Air Conditioning & Electrical is proud to offer superior heating maintenance for your furnaces and heat pumps to ensure they work at peak performance on even the coldest days.<\/p>\n

With over 85 years in the industry, our technicians have the skills and training to provide outstanding service and effective, affordable solutions for all your HVAC needs.<\/p>\n

Call our experts at (555) 555-5555<\/a>\u00a0today to <\/strong>schedule heating maintenance<\/a> in Georgetown or nearby<\/strong>.<\/strong><\/p>\n

What Is A Heating Maintenance Check?<\/h2>\n

At F.H. Furr the safety of you, your family and your home are our first priority.\u00a0 Your Maintenance & Safety Inspection Technician will investigate and share with you, any & all safety related matters that we uncover.\u00a0 We will also identify any maintenance your system may need for maximum efficiency, comfort, reliability, and longevity.\u00a0 During your Maintenance & Safety Inspection, our service technician will perform a 36-point inspection\u00a0<\/strong>of your home heating system that will take about an hour or so to complete.\u00a0This includes, but is not limited to the following:\u00a0<\/strong><\/p>\n

    \n
  • Inspect air filtration system<\/li>\n
  • Run test to verify proper sequence of operation<\/li>\n
  • Check for safe combustion\n
      \n
    • Flame rollout \/ hard ignition \/ back pressure<\/li>\n
    • Carbon Monoxide<\/li>\n
    • Gas pressure(s)\u00a0<\/li>\n
    • Temperature rise \u2013 ensure within manufacturer specifications<\/li>\n
    • Test for gas leaks<\/li>\n<\/ul>\n<\/li>\n
    • Clean the flame sensor<\/li>\n
    • Inspect the heat exchanger for corrosion, cracks, pinholes, deformities or carbon\/soot.<\/li>\n
    • Inspect gas valve for corrosion, restriction of gas flow, and abnormal noise<\/li>\n
    • Inspect vent connectors for integrity, pitch, obstructions and leaks<\/li>\n
    • Inspect furnace controls and safety devices for integrity & proper operation<\/li>\n
    • Flush drain (90%+ efficient units only)<\/li>\n
    • Inspect electrical connections, wiring harness & disconnect (as applicable)<\/li>\n
    • Measure and document electrical parameters, such as\n
        \n
      • Incoming voltage<\/li>\n
      • Amp draw of blower motor<\/li>\n
      • Amp draw of inducer motor<\/li>\n
      • Amp draw of Compressor (heat pump only)<\/li>\n
      • Amp draw of Electric backup heater (heat pump only)<\/li>\n
      • Investigate any improper resistance that may be found in the electrical circuit.<\/li>\n<\/ul>\n<\/li>\n
      • Inspect capacitor(s) for integrity, corrosion and capacitance<\/li>\n
      • Inspect readily accessible ducts for integrity, cleanliness, and\/or obvious air leaks<\/li>\n
      • Inspect blower for proper \/ adequate air flow.\n
          \n
        • Includes Inspection of wheel, motor (& lubricate as needed)<\/li>\n
        • Check for cleanliness of indoor coil and secondary heat exchanger<\/li>\n
        • Check for cleanliness of the outdoor coil (heat pumps only)<\/li>\n<\/ul>\n<\/li>\n
        • Vacuum loose debris from the blower and burner compartments<\/li>\n
        • Wipe clean the reachable areas of the unit cabinet<\/li>\n
        • Replace filter if\/when provided by the customer while on-site at the time of inspection<\/li>\n
        • Check and calibrate thermostat as required<\/li>\n
        • Inspect the entire furnace\/boiler for loose or worn parts and abnormal vibrations<\/li>\n
        • Test and adjust the unit for peak operating efficiency<\/li>\n
        • Check defrost cycle and reversing valve operation (heat pumps only)<\/li>\n
        • Check the crankcase heater for proper maintenance (heat pumps only)<\/li>\n
        • Check refrigerant level (heat pumps only)<\/li>\n
        • Check emergency heat systems for proper operation (heat pumps only)<\/li>\n<\/ul>\n

          Your F.H. Furr Maintenance & Safety Inspection, satisfies the manufacture\u2019s requirements for annual inspection by a licensed contractor.\u00a0 It will also keep you informed on any additional maintenance that may be needed to keep your system running safely, reliably & efficiently for a long time.\u00a0<\/p>\n